cc/td/doc/product/rtrmgmt/cw2000/dfm
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

Status of DFM Device Agent Bugs (DFM 1.x and DFM 2.x)


Status of DFM Device Agent Bugs (DFM 1.x and DFM 2.x)

Table 1 lists known problems with how DFM interacts with specific Cisco device agents. To determine whether these bugs are due to a problem with DFM or a problem with a device SNMP agent, bugs have been opened against both DFM and the specific devices.

Table 2 lists the DFM agent-based problems which have been resolved.

This document is updated when a new patch/IDU is released. Unless noted in the Explanation, the problem does not have a workaround.

Note The base version of DFM 2.0 includes all device support through DFM 1.2.8.

To obtain more information about any of these problems, access the Cisco Software Bug Toolkit by logging into Cisco.com at http://www.cisco.com/cgi-bin/Support/Bugtool/home.pl.

To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm.

Table 1 Known Problems Under Investigation 

Bug ID
Summary
Explanation
Supported in DFM...

CSCsa58213

WLSE: switchover trap not supported

When a WLSE switchover occurs (from standby to active), DFM does report an event but the switchover trap is not reported. A device bug will be opened.

1.2.10

CSCsa45853

CDM 4630: Port/IF alarms not generated

The CDM 4630 does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps. A device bug will be opened.

1.2.10

CSCsa53666

Cat 4948: Port/IF alarms not generated

The Catalyst 4948 does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps. A device bug will be opened.

1.2.10

CSCsa45336

AP 340: Port/IF alarms not generated

The AP 340 does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps. A bug has been opened against the AP 340 (CSCeg68198).

1.2.10

CSCsa45304

MWR-1900: Port/IF alarms not generated

The MWR-1900 does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps. A bug has been opened against the MWR-1900 (CSCsa13224).

1.2.10

CSCsa47035

CE-2636: Port/IF alarms not generated

The CE-2636 does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps. A bug has been opened against the CE-2636 (CSCeg61459).

1.2.10

CSCsa46826

CDM 4630: Disk and processor events not generated

Because the CDM 4630 does not implement the Host Resources MIB, DFM does not generate disk and processor events. A device bug will be opened.

1.2.10

CSCsa36885

WS-SVC-CMM does not fully implement ifXTable

DFM does not generate the following symptoms for the WS-SVC-CMM: HighUtilizationRate, HighDiscardRate, HighCollisionRate, HighBroadcastRate, HighQueueDropRate, and HighErrorRate. This is because a number of OIDs are not implemented in the ifXTable. A bug has been opened against the WS-SVC-CMM (CSCin83708).

1.2.10

CSCsa23445

2600/3600 NAM: Port/IF alarms not generated

The 2600/3600 NAM does not compute CurrentUtilization because HighCounter MIBs are not implemented for interfaces with speeds greater than 20 Mbps.

A bug has been opened against the 2600/3600 NAM (CSCef18043).

1.2.9

CSCsa23167

MWR 1900 does not report RepeatedRestarts

The MWR 1900 does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps. A bug has been opened against the MWR 1900 (CSCee75859).

1.2.9

CSCsa23158

AP 340 does not report RepeatedRestarts

The AP 340 does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps. A bug has been opened against the AP 340 (CSCee76825).

1.2.9

CSCsa25319

CDM-4630 does not report RepeatedRestarts when host listening to custom ports

If a host is listening to custom ports, the CDM-4630 does not send traps to the host. In this situation, no RepeatedRestarts alarms are generated. A bug has been opened against the CDM-4630 (CSCee94244).

1.2.9

CSCsa22854

4908G-L3 does not report RepeatedRestarts

The 4908G-L3does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps. A bug has been opened against the 4908G-L3 (CSCee76829).

1.2.9

CSCsa23445

2600/3600 NAM does not support network adapter alarms on interfaces greater than 20,000,000 mbps

The 2600/3600 NAM does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. This is because the ifHCInOctets and ifHCOutOctets variables are not implemented. A bug against the 2600/3600 NAM (CSCef18043).

1.2.9

CSCsa13092

MWR-1941-DC does not report RepeatedRestarts

The Cisco MWR-1941-DC router does not support the RepeatedRestarts symptom because the device does not generate cold start and warm start traps. A bug has been opened against the MWR-1941-DC (CSCin73592).

2.0,
1.2.8

CSCsa13224

MWR-1941-DC does not generate FE HighUtilization, HighQueueDropRate, HighCollisionRate, HighErrorRate

The MWR-1941-DC does not support the HighUtilization, HighQueueDropRate, HighCollisionRate, or HighErrorRate symptoms on Fast Ethernet interfaces. This is because the HCInOctets MIB attribute is not implemented. A bug against the MWR-1941-DC (CSCin73594).

2.0,
1.2.8

CSCsa13482

GSS 4490 does not report RepeatedRestarts

The CiscoGSS 4490 does not support the RepeatedRestarts symptom because the device does not generate cold start and warm start traps. A bug has been opened against the GSS 4490 (CSCin73595).

2.0,
1.2.8

CSCsa14622

GSS-4490 does not generate processor HighUtilization or disk OperationallyDown

The GSS-4490 does not support the processor HighUtilization or disk OperationallyDown symptoms. This is because the hrProcessorLoad and hrDeviceStatus MIB attributes are not implemented. A bug against the GSS-4490 (CSCin73597).

2.0,
1.2.8

CSCsa15955

2948-GL3 does not report RepeatedRestarts

The Cisco 2948-GL3 does not support the RepeatedRestarts symptom because the device does not generate cold start and warm start traps. A bug has been opened against the 2948-GL3 (CSCin73590).

2.0,
1.2.8

CSCin63247

3220 does not support network adapter alarms on interfaces greater than 100 mbps

The Cisco 3220 does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. A bug has been opened against the Cisco 3220 (CSCin63022).

2.0,
1.2.7

CSCin63249

MWAM does not support network adapter alarms on interfaces greater than 100 mbps

The Cisco Multiprocessor WAN Application Module (MWAM) does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. This is because several MIB variables are not implemented. A bug against the MWAM (CSCin63100).

2.0,
1.2.7

CSCin63251

RPM-PR does not support network adapter alarms on interfaces greater than 100 mbps

The Cisco Route Processor Module (RPM-PR) RPM-PR does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. This is because several MIB variables are not implemented. A bug against the RPM-PR (CSdy89558).

2.0,
1.2.7

CSCin63245

IAD 2430 does not support network adapter alarms on interfaces greater than 100 mbps

The Cisco IAD 2430 Series Integrated Access Device does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. A bug has been opened against the IAD 2430 (CSCin63018).

2.0,
1.2.7

CSCin65543

ONS 15501-AC power supply is not populated in DFM GUI

The Cisco ONS 15501-AC does not display its power supply when a user expands the ComposedOf tree. (This does not occur on the ONS 15501-DC). A bug has been opened against the ONS 15501-AC (CSCin66271).

2.0,
1.2.7

CSCsa06505

SN-5428 does not report HighQueueDropRate

The Cisco SN-5428 storage router does not support the HighQueueDropRate fault. This is because the locIfInputQueueDrops MIB variable is not implemented. A bug against the SN-5428 (CSCin65053).

2.0,
1.2.7

CSCsa07015

VPN 3000 does not report RepeatedRestarts

The Cisco VPN 3000 router does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps. A bug has been opened against the VPN 3000 (CSCdt01583).

2.0,
1.2.7

CSCsa07046

ONS 15501-DC does not generate DuplicateIP error

DFM does not report DuplicateIP events for the ONS 15501-DC. A bug has been opened against the ONS 15501-DC (CSCin67711).

2.0,
1.2.7

CSCsa02381

10720 does not report VoltageOutOfRange

The 10720 router does not support the VoltageOutOfRange alarm because the device does not support the following MIB variables:

•ciscoEnvMonVoltageStatusValue

•ciscoEnvMonVoltageThresholdLow

•ciscoEnvMonVoltageThresholdHigh

A bug has been opened against the Cisco 10720 (CSCin60106).

2.0,
1.2.6

CSCsa02578

ONS 15530 CurrentUtilization for FE interface is grayed out

DFM does not report CurrentUtilization for FE interfaces on ONS 15530 NEBS, ETSI, and ESPX devices because ifHCounters are not implemented. A bug has been opened against the ONS 15530 (CSCec44897).

2.0,
1.2.6

CSCsa02981

CE-7325 does not support RepeatedRestarts

The CE-7325 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A bug has been opened against the CE-7325 (CSCin58529).

2.0,
1.2.6

CSCea02995

7513MX CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco 7513MX because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.) A bug has been opened against the Cisco 7513MX (CSCea02914).

2.0,
1.2.4

CSCea03541

PIX 535 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco PIX 535 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. A bug has been opened against the PIX 535 (CSCea04950).

2.0,
1.2.4

CSCdz81075

WSC-SVC-NAM-1 and -NAM-2 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the WSC-SVC-NAM-1 and -NAM-2 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. A bug has been opened against the WSC-SVC-NAM-1 and -NAM-2 (CSCdz81059).

2.0,
1.2.4

CSCdz69718

3631 does not support RepeatedRestarts alarm.

The Cisco 3631 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps.

AA bug has been opened against the Cisco 3631 (CSCdz69704).

2.0,
1.2.4

CSCdy69761

3640: high utilization for serial interface is over 100%

The Cisco 3640 interface utilization computation is erroneous, sometimes resulting in utilization values over 100%.A device agent bug (CSCdy89115).

2.0,
1.2.4

CSCdx24447

VG200: DFM does not display T1 interfaces

When a VG200 is added to DFM, DFM displays it as Unsupported. In addition, T1 interfaces are not displayed. A device bug will be opened.

2.0,
1.2

CSCdx34570

Cat6000+MSFC: PowerDown event not getting cleared

The Catalyst 6000 with an MSFC does not clear a power down event after a module is powered down and powered back up. A device bug will be opened.

2.0,
1.2

CSCdt64368

AS5300: cold/warm start trap not generated

The AS5300 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A device bug will be opened.

2.0,
1.1

CSCdp88058

7200VXR: cold/warm start trap not generated

The 7200 VXR does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A device bug will be opened.

2.0,
1.0

CSCdt63744

3640: cold/warm start trap not generated

The Cisco 3640 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A device bug will be opened.

2.0,
1.0

CSCdr00300

8540 MSR: cold/warm start trap not generated

The 8540 MSR does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A device bug will be opened.

2.0,
1.0

CSCdr04559

8540 MSR: duplex info not known

DFM does not correctly compute interface utilization on the 8540 MSR because the device has not correctly implemented the SNMP MIB. A device bug will be opened.

2.0,
1.0

CSCdr00318

8540 MSR: module down not reported

The 8510 MSR does not generate a card down event after a card is removed. A device bug will be opened.

2.0,
1.0

CSCdp85901

8510 CSR: module down not reported

The 8510 CSR does not generate a card down event after a card is removed. A device bug will be opened.

2.0,
1.0

CSCdp85997

8510 CSR: duplex information not generated

DFM does not correctly compute interface utilization on the 8510 CSR.A device bug will be opened.

2.0,
1.0

CSCdp88115

7200 VXR: module down not reported

The 7200 VXR does not generate a card down event after a card is removed. A device bug will be opened.

2.0,
1.0

CSCdr57293

Cat6000:%utilization shown as 394.6%

The Catalyst 6000 interface utilization computation is erroneous, sometimes resulting in utilization values over 100%.A device bug will be opened.

2.0,
1.0

CSCdp68659

7000 routers: cold/warm start trap not generated

The Cisco 7000 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps. A device bug will be opened.

2.0,
1.0


Table 2 Resolved/Closed Problems 

Bug ID
Summary
Explanation
Supported in DFM...

CSCsa38656

WLSE does not fully implement MIB-II ifTable

DFM does not generate the following symptoms for the WLSE: HighDiscardRate, HighCollisionRate, HighBroadcastRate, HighQueueDropRate, and HighErrorRate. This is because several OIDs are not implemented in the ifXTable. These bugs have been closed because the device team does not plan to add this support.

1.2.10

CSCsa36887

Cisco 2801 does not fully implement ifXTable

DFM does not generate the following symptoms for the Cisco 2801: HighUtilization, HighDiscardRate, HighCollisionRate, HighBroadcastRate, HighQueueDropRate, and HighErrorRate. This is because several OIDs are not implemented in the ifXTable.

This problem does not occur if the following (or higher) IOS version is installed:

012.003

1.2.10

CSCsa33726

1841: Port/IF alarms not generated

1841 does not implement High Counters MIB. 1841 has two interfaces of type ethernetCsmacd(6) and speed 100000000 and hence the Network adapter related alarms are not generated in DFM. This problem does not occur if the following (or higher) IOS version is installed:

12.3 PI6

1.2.10

CSCsa26774

AP 340 does not generate DuplicateIP event

DFM does not report DuplicateIP events for the AP 340 because the IpAddr table is not populated for AP radio interfaces. Although a bug was opened against the AP 340, this DFM bug has been closed because the AP 340 will not have future releases in which this bug can be fixed.

1.2.9

CSCsa26774

AP 340 does not generate DuplicateIP event

DFM does not report DuplicateIP events for the AP 340 because the IpAddr table is not populated for AP radio interfaces. Although a bug was opened against the AP 340, this DFM bug has been closed because the AP 340 will not have future releases in which this bug can be fixed.

1.2.9

CSCin72033

CE-7320 does not report RepeatedRestarts

The Cisco CE-7320 content engine does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps.

This problem does not occur if the following (or higher) ACNS versions are installed:

005.001(003.001), 005.002(000.002)

2.0,
1.2.8

CSCin72028

Catalyst 6000 SSL module does not generate SNMP Unresponsive

After changing the SNMP community string setting in the Catalyst 6000 SSL module, DFM does not report an SNMP Unresponsive alarm. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.8

CSCsa12752

SOHO-78 does not generate SNMP Unresponsive

After changing the SNMP community string setting in the SOHO-78, DFM does not report an SNMP Unresponsive alarm. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.8

CSCsa13093

MWR-1941-DC does not generate SNMP Unresponsive

After changing the SNMP community string setting in the MWR-1941-DC, DFM does not report an SNMP Unresponsive symptom. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.8

CSCsa14191

CE-507, 507-AV, 560, 560-AV, 590 do not report RepeatedRestarts

The Cisco CE-507, CE-507-AV, CE-560, CE-560-AV, and CE-590 content engines do not support the RepeatedRestarts symptom because the devices do not generate cold start and warm start traps.

This problem does not occur if the following (or higher) ACNS versions are installed:

5.2.0

2.0,
1.2.8

CSCsa18753

Content Engines memory components not created

Memory components not created for Cisco Content Engine devices This is because the hrstoragetype attribute is returning incorrect values.

This problem does not occur if the following (or higher) ACNS versions are installed:

5.2.0

2.0,
1.2.8,
1.2.6

CSCin63477

827H router: SNMPAgent Unresponsive alarm is not generated

After changing the SNMP community string setting in the 827H router, DFM does not report an SNMP Unresponsive alarm. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.7

CSCsa07592

Cisco 6260: SNMPAgent Unresponsive alarm is not generated

After changing the SNMP community string setting in the Cisco 6260, DFM does not report an SNMP Unresponsive alarm. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.7

CSCsa07418

1710 VPN does not support network adapter alarms on interfaces greater than 100 mbps

The Cisco 1710 VPN does not support network adapter alarms for interfaces with speeds greater than 20,000,000 mbps. This is because the ifHCInOctets and ifHCOutOctets variables are not implemented.

This problem does not occur if the following (or higher) IOS versions are installed:

12.3(07.02)T, 012.003(007.002)

2.0,
1.2.7

CSCsa05906

MDS 9120 does not report RepeatedRestarts

The Cisco MDS 9120 switch does not support the RepeatedRestarts fault because the device does not generate cold start and warm start traps.

This problem does not occur if the following (or higher) IOS versions are installed:

1.3(1.12), 2.0(0.18)

2.0,
1.2.7

CSCin58260

10720 does not report RepeatedRestarts

It was thought that he 10720 router did not support the RepeatedRestarts alarm because the device did not generate cold start and warm start traps. This bug was closed since it was not a problem with the device, but with the trap viewer.

2.0,
1.2.6

CSCsa02822

uBR 7246VXR: SNMPAgent Unresponsive alarm not generated

After changing the SNMP community string setting in the uBR 7246VXR, DFM does not report an SNMP Unresponsive alarm. This problem was fixed in patch/IDU 1.2.10 and 2.0.1, which introduced a new symptom called InvalidResponse (see CSCsa26950 using the Bug Navigator, as described at the beginning of this document). To download the latest patch/IDU, log in to Cisco.com and point your browser to: http://www.cisco.com/cgi-bin/tablebuild.pl/cw2000-dfm

2.0,
1.2.6

CSCin58260

10720 does not report RepeatedRestarts

It was thought that he 10720 router did not support the RepeatedRestarts alarm because the device did not generate cold start and warm start traps. This bug was closed since it was not a problem with the device, but with the trap viewer.

2.0,
1.2.6

CSCsa03070

Catalyst 2970-24 does not generate DuplicateIP event

DFM does not report DuplicateIP events for the Catalyst 2970-24.

This problem does not occur if the following (or higher) IOS version is installed:

12.1(19)EA1

2.0,
1.2.6

CSCeb20298

3725 does not support performance events

DFM does not report any performance-related events on the Cisco 3725 because the ifX table is not properly implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation.

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.2(16.01)T

2.0,
1.2.5

CSCeb20571

3725 does not always support RepeatedRestarts

The Cisco 3725 does not support the Repeated Restarts alarm because, although the device generates cold start and warm start traps, the traps are not received in the local subnet upon startup. They are received outside the subnet.

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.2(16.01)T

2.0,
1.2.5

CSCdz68098

3631 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco 3631 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.)

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW0,3 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.3(14.06)PI01, 12.3(14.06)PI00, 12.2(14.06)T

2.0,
1.2.4

CSCdz69210

1751V CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco 1751V because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.)

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.3(14.06)PI01, 12.3(14.06)PI00, 12.2(14.06)T

2.0,
1.2.4

CSCdz69202

1721 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco 1721 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.)

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.3(14.06)PI01, 12.3(14.06)PI00, 12.2(14.06)T

2.0,
1.2.4

CSCdz74246

2691 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco 2691 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.)

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.2(16.01)T

2.0,
1.2.4

CSCea03550

AP1100 CurrentUtilization for FE interface is grayed out.

DFM does not report CurrentUtilization for FE interfaces on the Cisco Aironet AP1100 because the ifX table is not completely implemented. The cause is under investigation; it may be due to a problem with the device MIB implementation. (There is no support for the ifHCInOctets and ifHCOutOctets MIB attributes.)

This problem does not occur if the following (or higher) IOS version is installed:

12.2(11)JA

2.0,
1.2.4

CSCdz69758

1751V does not support RepeatedRestarts alarm.

The Cisco 1751V does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps.

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(17a)SX, 12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.3(14.06)PI01, 12.2(15.01)S, 12.3(14.06)PI00, 12.2(14.06)T, 012.002(015.001)

2.0,
1.2.4

CSCdz69748

1721 does not support RepeatedRestarts alarm.

The Cisco 1721 does not support the RepeatedRestarts alarm because the device does not generate cold start and warm start traps.

This problem does not occur if the following (or higher) IOS versions are installed:

12.2(17a)SX, 12.2(16)BX, 12.3(00.05)BW03, 12.2(16)B, 12.2(15)ZN, 12.2(16.01)B, 12.3(14.06)PI01, 12.2(15.01)S, 12.3(14.06)PI00, 12.2(14.06)T, 012.002(015.001)

2.0,
1.2.4

CSCdz81046

WSC-SVC-NAM-1 and -NAM-2 do not support RepeatedRestarts alarm.

The WSC-SVC-NAM-1 and -NAM-2 do not support the Repeated Restarts alarm because the devices do not generate cold start and warm start traps.

This problem does not occur if the following (or higher) NAM software version is installed:

003.001(000.016)

2.0,
1.2.4


hometocprevnextglossaryfeedbacksearchhelp

Posted: Thu Feb 24 18:06:21 PST 2005
All contents are Copyright © 1992--2005 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.